Have a question? Give us a call: +86-577-6270-6808

Products

  • Copper Earthing Strip jumper

    Copper Earthing Strip jumper

    Copper strip terminal jumper

    Singler wire Cu ETP UNI 5649-71.Similar to DIN 72333

  • HD Cu tube butt copper splice crimping BN connector

    HD Cu tube butt copper splice crimping BN connector

    BN series copper cable connections are applicable for the connection of the circular wire with power supply cable in distribution equipment. They are made of tin coated 99.9% pure copper tube.

  • HD Cu tube butt copper splice crimping GTY connector

    HD Cu tube butt copper splice crimping GTY connector

    GTY series copper cable connections are applicable for the connection of the circular wire with power supply cable in distribution equipment. They are made of tin coated 99.9% pure copper tube.

  • Porcelain Dropout Fuse Cutout

    Porcelain Dropout Fuse Cutout

    Drop-out fuse cutout and load switching fuse cutout are of outdoor used high voltage protective device,Tobe connected with incomin-g feeder of distribution transformer or distribution lines,it mainly protect transformer or lines from short circuit and overload,and on/off loading,current,Drop-out fuse cutout is composed of insulate insulator supports and fuse tube,static contacts is fixed on two sides of insulator support and moving contact is installed on two ends of fuse tube,Fuse tube is composed of inside arcexting tube.Outer phenolic compound paper tube or epoxy glasstube,Load switching fuse cutout provides enfored elastic auxiliry contacts and arc-extinguishing exclosure switching on-off loading current.
    At normally working via fuselink tightened the fuse tube is fixfed to form up of close position.In case system occure faults,fault current result result in fuse melt immediately and take piece electric are,which let arc-extinguishing tube being heated and fexplode a lot of gas,Th-os will produce high pressure and below of the are along with tube. After fuselink melt melt moving contact has no tightened strength again,mecganismis locked and fuse tube drop out, Cutout now is in open position,When it needs to switch off during cutout loading,operat-or shall via insulating operating bar pull the moving contact,atits beginning main contact and auxiliary static contactic contactedst-ill, Whiling pulling the auxiliary contact is separated between auxiliary contacts there occur electric arc and the arc will be lengthene-d in arc-extinguishing enclosure gap and meanwhile arc-exting explode gas to blow off the arc during current passing zero.

  • Rod To Tape Clamp-RCC16B

    Rod To Tape Clamp-RCC16B

    Earth Rod To Cable Clamp  brass cable clamp used to connect the copper rod and the conductor cable. It can well install and easily to use.Providing a secure connection between the down conductor cable and rod.

  • Rod To Tape Clamp-RCCA

    Rod To Tape Clamp-RCCA

    Earth Rod To Cable Clamp  brass cable clamp used to connect the copper rod and the conductor cable. It can well install and easily to use.Providing a secure connection between the down conductor cable and rod.

  • Stainless Steel Earth Rod-SER

    Stainless Steel Earth Rod-SER

    Stainless Steel Earth Rod-SER

     

    Stainless steel rods are used to overcome many of the problems caused by galvanic corrosion which can take place between dissimilar metals buried in close proximity. Furse stainless steel earth rods are highly resistant to corrosion.

     

    A kit include rod, drving head coupling dowel, driving stud and spike to make 8 ft rod.

    Connections to the rods can be by mechanical clamps, compression.

     

    Standard: BS EN 50164-2, BS7430, UL467

  • Copper Claded Non Magnetic Steel Earth Rods-CCR

    Copper Claded Non Magnetic Steel Earth Rods-CCR

    Copper Claded Non Magnetic Steel Earth Rods

     

    Copper claded earth rods are made from 99. 9 % pure electrolytic copper tube  and non magnetic steel

     

    This product claded copper thickness more than 1.5mm,so the conductive good performance,low resistance, and can be comparable to pure copper ground rod.

  • Solid Copper Earth Rod-CER

    Solid Copper Earth Rod-CER

    Solid Copper and Stainless Steel Earth Rod-CER

     

    Solid copper earth rods  greater resistance to corrosion . They are ideally used in applications where soil conditions are very aggressive, such as soils with high salt content.

     

    Kit include rod, driving head coupling dowel, driving spike to make  8  ft rod. Connections to the rods can be by mechanical clamps, compression.

     

    Standard: BS EN 50164-2, BS7430, UL467

  • Copper Bonded Earth Rod (Un-Thread)-ER

    Copper Bonded Earth Rod (Un-Thread)-ER

    Copper Bonded Earth Rod(Un-Thread)

     

    Copper bonded earth rods probably offer to the installer the best and most economical earth rods available . They are made by molecularly bonding 99.9% pure electrolytic copper on to a low carbon steel core.

    Copper thickness standard 250 microns.(others plating copper thickness as your requested)

    Earth rods to BS EN 50164-2, Bs7430 and Ul467 ,Fittings to BS EN 50164-1

  • Copper Bonded Earth Rod- ERT

    Copper Bonded Earth Rod- ERT

    Copper Bonded Earth Rod

    Copper bonded earth rods probably offer to the installer the best and most economical earth rods available. They are made by molecularly bonding 99.9% pure electrolytic copper on to a low carbon steel core.

     

    Confusion often arises between thread and shank diameters for threaded rods. The thread rolling process, used by quality rod manufacturers, raises the surface of the rod so that thread diameter (B) is greater than shank diameter (A) (see drawing).

     

    Copper thickness standard 254 microns.(others plating copper thickness as your requested)

     

    Earth rods to BS EN 50164-2, Bs7430 and UL467; Fittings to BS EN 50164-1

  • JG-A Copper Cable Lug

    JG-A Copper Cable Lug

    Copper Cable Lug JGA
    The lugs are made from high conductivity annealed copper which gives the best electrical properties possible.
    Material:copper-99.9% pure.
    Operating Temperature:-55℃ to 155℃ due to oxygen-free copper
    Surface:Tin plated