Earthing Protection Accessories
-
PAL Metal Tension Clamp
The PAL Tension Clamp are used to anchor and tighten LV-ABC lines with insulated neutral messenger.These clamps are easy to install without tools and suitable for various climatic conditions.
-
Porcelain Dropout Fuse Cutout
Drop-out fuse cutout and load switching fuse cutout are of outdoor used high voltage protective device,Tobe connected with incomin-g feeder of distribution transformer or distribution lines,it mainly protect transformer or lines from short circuit and overload,and on/off loading,current,Drop-out fuse cutout is composed of insulate insulator supports and fuse tube,static contacts is fixed on two sides of insulator support and moving contact is installed on two ends of fuse tube,Fuse tube is composed of inside arcexting tube.Outer phenolic compound paper tube or epoxy glasstube,Load switching fuse cutout provides enfored elastic auxiliry contacts and arc-extinguishing exclosure switching on-off loading current.
At normally working via fuselink tightened the fuse tube is fixfed to form up of close position.In case system occure faults,fault current result result in fuse melt immediately and take piece electric are,which let arc-extinguishing tube being heated and fexplode a lot of gas,Th-os will produce high pressure and below of the are along with tube. After fuselink melt melt moving contact has no tightened strength again,mecganismis locked and fuse tube drop out, Cutout now is in open position,When it needs to switch off during cutout loading,operat-or shall via insulating operating bar pull the moving contact,atits beginning main contact and auxiliary static contactic contactedst-ill, Whiling pulling the auxiliary contact is separated between auxiliary contacts there occur electric arc and the arc will be lengthene-d in arc-extinguishing enclosure gap and meanwhile arc-exting explode gas to blow off the arc during current passing zero. -
Rod To Tape Clamp-RCC16B
Earth Rod To Cable Clamp brass cable clamp used to connect the copper rod and the conductor cable. It can well install and easily to use.Providing a secure connection between the down conductor cable and rod.
-
Rod To Tape Clamp-RCCA
Earth Rod To Cable Clamp brass cable clamp used to connect the copper rod and the conductor cable. It can well install and easily to use.Providing a secure connection between the down conductor cable and rod.
-
Stainless Steel Earth Rod-SER
Stainless Steel Earth Rod-SER
Stainless steel rods are used to overcome many of the problems caused by galvanic corrosion which can take place between dissimilar metals buried in close proximity. Furse stainless steel earth rods are highly resistant to corrosion.
A kit include rod, drving head coupling dowel, driving stud and spike to make 8 ft rod.
Connections to the rods can be by mechanical clamps, compression.
Standard: BS EN 50164-2, BS7430, UL467
-
Copper Claded Non Magnetic Steel Earth Rods-CCR
Copper Claded Non Magnetic Steel Earth Rods
Copper claded earth rods are made from 99. 9 % pure electrolytic copper tube and non magnetic steel
This product claded copper thickness more than 1.5mm,so the conductive good performance,low resistance, and can be comparable to pure copper ground rod.
-
Solid Copper Earth Rod-CER
Solid Copper and Stainless Steel Earth Rod-CER
Solid copper earth rods greater resistance to corrosion . They are ideally used in applications where soil conditions are very aggressive, such as soils with high salt content.
Kit include rod, driving head coupling dowel, driving spike to make 8 ft rod. Connections to the rods can be by mechanical clamps, compression.
Standard: BS EN 50164-2, BS7430, UL467
-
Copper Bonded Earth Rod (Un-Thread)-ER
Copper Bonded Earth Rod(Un-Thread)
Copper bonded earth rods probably offer to the installer the best and most economical earth rods available . They are made by molecularly bonding 99.9% pure electrolytic copper on to a low carbon steel core.
Copper thickness standard 250 microns.(others plating copper thickness as your requested)
Earth rods to BS EN 50164-2, Bs7430 and Ul467 ,Fittings to BS EN 50164-1
-
Copper Bonded Earth Rod- ERT
Copper Bonded Earth Rod
Copper bonded earth rods probably offer to the installer the best and most economical earth rods available. They are made by molecularly bonding 99.9% pure electrolytic copper on to a low carbon steel core.
Confusion often arises between thread and shank diameters for threaded rods. The thread rolling process, used by quality rod manufacturers, raises the surface of the rod so that thread diameter (B) is greater than shank diameter (A) (see drawing).
Copper thickness standard 254 microns.(others plating copper thickness as your requested)
Earth rods to BS EN 50164-2, Bs7430 and UL467; Fittings to BS EN 50164-1
-
Earth Bar Insulator SM
Bus Bar Insulator
Powerlink earth bar combine with high mechanical stregth with high arc resistance and dielectric properties at elevated temperatures and humidity. Material use BMC or SMC. The bolts regular type is brass also can do stainless steel. Also can make according to the customer requested.
-
JY/LY splicing tube and insulation cover
Place of Origin: Zhejiang, China
Brand Name: Pengyou
Model Number: GLB
Type: Connector
Application: Wire Connecting,
Material: Aluminum
Size: 1.5-630mm²
Certificate: CE,RoHS,ISO9000
Purity: 0.999
Sample: Freely Supplied
-
C type copper connecting clamp crimp Connectors
Place of Origin: Zhejiang, China
Brand Name: Pengyou
Model Number: CCT
Type: Crimp Terminal
Product Name: Earthing Rod Clamps
Cable diameter: 7.5-700mm
Material: Copper
Certificate: ISO9001/CE/RoHs
Color: pure copper color
Application: Wire Connecting
CONWELL: Factory
OEM/ODM: Supply
Service: offer free sample